With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?
Select an option to see the answer and solution.
Networking · all questionsEIGRP and OSPF
EIGRP and OSPF
practice.
Practice every MCQ with options. Use Show answers when you want the correct option and solution.
19
Questions
1/1
Page
Pick an option on a question to see the right answer and solution.
Which of the following describe the process identifier that is used to run OSPF on a router?
1. It is locally significant.
2. It is globally significant.
3. It is needed to identify a unique instance of an OSPF database.
4. It is an optional parameter required only if multiple OSPF processes are running on the router.
1. It is locally significant.
2. It is globally significant.
3. It is needed to identify a unique instance of an OSPF database.
4. It is an optional parameter required only if multiple OSPF processes are running on the router.
Select an option to see the answer and solution.
A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?
Select an option to see the answer and solution.
What is the administrative distance of OSPF?
Select an option to see the answer and solution.
Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?
Select an option to see the answer and solution.
Where are EIGRP successor routes stored?
Select an option to see the answer and solution.
Which command will display all the EIGRP feasible successor routes known to a router?
Select an option to see the answer and solution.
Which is true regarding EIGRP successor routes?
1. A successor route is used by EIGRP to forward traffic to a destination.
2. Successor routes are saved in the topology table to be used if the primary route fails.
3. Successor routes are flagged as "active" in the routing table.
4. A successor route may be backed up by a feasible successor route.
5. Successor routes are stored in the neighbor table following the discovery process.
1. A successor route is used by EIGRP to forward traffic to a destination.
2. Successor routes are saved in the topology table to be used if the primary route fails.
3. Successor routes are flagged as "active" in the routing table.
4. A successor route may be backed up by a feasible successor route.
5. Successor routes are stored in the neighbor table following the discovery process.
Select an option to see the answer and solution.
Which EIGRP information is held in RAM and maintained through the use of Hello and update packets?
1. Neighbor table
2. STP table
3. Topology table
4. DUAL table
1. Neighbor table
2. STP table
3. Topology table
4. DUAL table
Select an option to see the answer and solution.
Which of the following are true regarding OSPF areas?
1. You must have separate loopback interfaces configured in each area.
2. The numbers you can assign an area go up to 65,535.
3. The backbone area is also called area 0.
4. If your design is hierarchical, then you don't need multiple areas.
5. All areas must connect to area 0.
1. You must have separate loopback interfaces configured in each area.
2. The numbers you can assign an area go up to 65,535.
3. The backbone area is also called area 0.
4. If your design is hierarchical, then you don't need multiple areas.
5. All areas must connect to area 0.
Select an option to see the answer and solution.
What are reasons for creating OSPF in a hierarchical design?
1. To decrease routing overhead
2. To speed up convergence
3. To confine network instability to single areas of the network
4. To make configuring OSPF easier
1. To decrease routing overhead
2. To speed up convergence
3. To confine network instability to single areas of the network
4. To make configuring OSPF easier
Select an option to see the answer and solution.
Which two of the following commands will place network 10.2.3.0/24 into area 0?
1.
2.
3.
4.
5.
1.
router eigrp 102.
router ospf 103.
network 10.0.0.04.
network 10.2.3.0 0.0.0.255 area05.
network 10.2.3.0 0.0.0.255 area 0Select an option to see the answer and solution.
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
Select an option to see the answer and solution.
Which of the following protocols support VLSM, summarization, and discontiguous networking?
1. RIPv1
2. IGRP
3. EIGRP
4. OSPF
5. BGP
6. RIPv2
1. RIPv1
2. IGRP
3. EIGRP
4. OSPF
5. BGP
6. RIPv2
Select an option to see the answer and solution.
You get a call from a network administrator who tells you that he typed the following into his router:
He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?
Router (config) #router ospf 1
Router (config-router) #network 10.0.0.0 255.0.0.0 area 0
Select an option to see the answer and solution.
Which of the following network types have a designated router and a backup designated router assigned?
1. Broadcast
2. Point-to-point
3. NBMA
4. NBMA point-to-point
1. Broadcast
2. Point-to-point
3. NBMA
4. NBMA point-to-point
Select an option to see the answer and solution.
Which type of OSPF network will elect a backup designated router?
1. Broadcast multi-access
2. Non-broadcast multi-access
3. Point-to-point
4. Broadcast multipoint
1. Broadcast multi-access
2. Non-broadcast multi-access
3. Point-to-point
4. Broadcast multipoint
Select an option to see the answer and solution.
You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?
Select an option to see the answer and solution.
Which of the following network types have a designated router and a backup designated router assigned?
1. Broadcast
2. Point-to-point
3. NBMA
4. NBMA point-to-point
Select an option to see the answer and solution.