There is a double faced friction disc splined to a shaft in the
A. Transmission
B. Differential
C. Engine
D. Clutch
Select an option to see the answer and solution.
The drive gear in the differential is adjusted by use of
A. Selective washers of proper thickness
B. Adjustment nuts
C. Adjustment screws
D. Gear box
Select an option to see the answer and solution.
Which types of joints are used when the shafts are inclined?
A. Universal joint
B. Hinge joint
C. Ball and socket joint
D. Pivot joint
Select an option to see the answer and solution.
The brake bleeding process removes from system
A. Air
B. Vacuum
C. Excess fluid
D. Excess pressure
Select an option to see the answer and solution.
A discharded lead-acid battery has on its plates
Select an option to see the answer and solution.
Which is the lowest part of the piston?
Select an option to see the answer and solution.
Which one of the statement is correct?
1. Petrol engine is a reciprocating engine
2. Petrol engine is high speed engine
3. Petrol engine uses petrol as fuel
4. Petrol engine is internal combustion engine
A. All four are correct
B. Only 1 is correct
C. Only 4 is correct
D. All are wrong
Select an option to see the answer and solution.
Parts of the clutch that should not be cleaned in solvent include the
A. Friction disc and throw out bearing
B. Friction disc cover
C. TIuow out bearing and springs
D. Release levers and springs
Select an option to see the answer and solution.
What are the general type of smoke?
A. White
B. Blue
C. Black
D. All are correct
Select an option to see the answer and solution.
The carbon from the cylinder head is removed with
A. Water
B. Caustic soda
C. Scraper
D. Soap
Select an option to see the answer and solution.
If the front of the front wheels is inside and rear of front wheels are apart when the vehicle is at rest, then the configuration is called?
A. Toe-in
B. Toe out
C. Positive camber
D. Positive castor
Select an option to see the answer and solution.
In a simple epicyclic gear set, the outpur member to increase torque in reverse is always the
A. Ring gear
B. Plant carrier
C. Sun gear
D. None of the above
Select an option to see the answer and solution.
Which of the following is the inside diameter of cylinder in which piston works up and down?
A. Stroke
B. Bore
C. Throw
D. Cycle
Select an option to see the answer and solution.
Fuel is fed to the carburettor in which of the following ways?
A. Gravity feed system
B. Forced feed system
C. Neither of them
D. A and B both
Select an option to see the answer and solution.
Radiator used in which of the following engines is heavy duty?
A. Petrol engine
B. Diesel engine
C. Both
D. None of these
Select an option to see the answer and solution.
What is the purpose of the reciprocating ball type steering gear?
A. To reduce the operating cost
B. To reduce the number of parts
C. To reduce the operating friction
D. To reduce the toe-out during the turns
Select an option to see the answer and solution.
The intake manifold is a . . . . . . . . tube for carrying the air fuel mixture from the carburettor to the engine intake port.
A. Cast iron
B. Aluminium
C. Both
D. None of these
Select an option to see the answer and solution.
Which of the following is correct?
A. I H P = 20 × 30 P L A N n
B. I H P = 20 × 10 P L A N n
C. I H P = 70 × 60 P L A N n
D. I H P = 10 × 10 P L A N n
Select an option to see the answer and solution.
Brake fade is
A. Loss of pedal
B. Loss of cefficient of friction
C. Loss of hydraulic fluid
D. None of these
Select an option to see the answer and solution.
As the load on the vehicle increase it demands
A. Increased braking torque
B. Decreased braking torque
C. Same braking torque
D. Same RPM
Select an option to see the answer and solution.