In centrifugal pump of . . . . . . . . construction impeller is mounted on the motor shaft.
A. Cubic
B. Monobloc
C. Rectangular
D. Solinoid
Select an option to see the answer and solution.
Underground transport arrangements are generally divided into . . . . . . . . categories.
Select an option to see the answer and solution.
The temperature of the coal drill is bring down by using . . . . . . . . fan.
A. Bowled
B. Rolled
C. Cowled
D. Speed
Select an option to see the answer and solution.
Which valve to enable the pump to be primed with water from the delivery column before starting up, and also small pump is not generally provided.
A. Retaing valve
B. Sluice valve
C. By pass valve
D. Air cock
Select an option to see the answer and solution.
Head gear should with stand
A. Live loads and wind pressure
B. Cage weight
C. Explosions
D. Rock Bursts
Select an option to see the answer and solution.
In gathering arm loader, Jib end can also be slewed through a horizontal plate so as to make an angle of . . . . . . . . to the axis of the machine either side.
Select an option to see the answer and solution.
Ropes used for CCMS.
A. Locked coil
B. Regular lay
C. Langs lay
D. Flattend strand
Select an option to see the answer and solution.
Difference between total discharge head and total suction head called . . . . . . . .
A. Head
B. Static head
C. Total head
D. Suction head
Select an option to see the answer and solution.
If the mine car type is Gable bottom, the mode of unloading provided is . . . . . . . .
A. Bottom opening
B. Both side tilting
C. Single side opening
D. Both side opening
Select an option to see the answer and solution.
The locked coil rope not used for . . . . . . . .
A. Winding
B. Guide rope
C. Splicing
D. None
Select an option to see the answer and solution.
A dimension less number used to characterise the turbo machinery, normalises impellars to in revolutions per minute to that of a geometrically similar impeller, if it where to deliver 1 gallon per minute against 1 foot of hydraulic head . . . . . . . .
A. Specific speed
B. Suction static left
C. Head
D. Suction static head
Select an option to see the answer and solution.
All the chains must be connected at least once in . . . . . . . . months.
Select an option to see the answer and solution.
In a few cases a Jack hammer may be mounted on . . . . . . . .
A. Stopper
B. Drifter
C. Sinker
D. Air leg
Select an option to see the answer and solution.
'Marrying' the word used in . . . . . . . .
A. Splicing
B. Capping
C. Haulage
D. Conveyor
Select an option to see the answer and solution.
In squiral cage motor and slip ring induction motor . . . . . . . . is similar.
A. Stator
B. Rotor
C. Both stator and rotor
D. None
Select an option to see the answer and solution.
On level road or raising in bye the tension bogey of endless haulage should be placed near the . . . . . . . .
A. Out bye pulley
B. In bye pulley
C. Haulage engine
D. All of these
Select an option to see the answer and solution.
A cage which can accommodate two tubes called . . . . . . . .
A. Deck cage
B. Multi cage
C. Tanden cage
D. Single cage
Select an option to see the answer and solution.
Detaching hooks are not employed in . . . . . . . . winding.
A. Friction
B. Cage
C. Skip
D. None
Select an option to see the answer and solution.
Rock and pinion is used for . . . . . . . .
A. Large spend reduction
B. To convert rotory motion to linier motion
C. Convert vertical motion to vertical motion
D. To recude and convert liner motion into rotary motion
Select an option to see the answer and solution.
Now a days use of CCM has become obsolate due to introduction of
A. Delay action detonators
B. Coal plough
C. DERDS
D. Continuous miner
Select an option to see the answer and solution.