Most of the high explosives blasted with the help of detonator said to be
A. Fuse sensitive
B. Cap sensitive
C. Non-cap sensitive
D. All of these
Select an option to see the answer and solution.
Specifications of stone dust should be tested once in . . . . . . . . months.
Select an option to see the answer and solution.
Wind rose is used to show
A. Air pollution
B. Air velocity
C. Air blast
D. Air flow direction
Select an option to see the answer and solution.
Maximum velocities of ventilating air at other roadways.
A. 4 m/sec
B. 4.8 m/sec
C. 6 m/sec
D. 8 m/sec
Select an option to see the answer and solution.
The main mine fan has to run for all . . . . . . . . days.
Select an option to see the answer and solution.
Deck loading is very useful when
A. strata consists of soft rocks
B. strata consists of friable rocks
C. strata consists of alternate band of hard and softer rocks
D. seam water bearance is high
Select an option to see the answer and solution.
It would be advisable to design the ventilation system on the basis of . . . . . . . .
A. Dry bulb temperature
B. RH
C. Cooling power
D. Wet bulb temperature
Select an option to see the answer and solution.
It is good practice to select a station where there is no area changes particularly on the upstream side (ventilation survey) should atleast.
A. Five roadway diameter
B. Eight roadway diameter
C. Ten roadway diameter
D. Two roadway diameter
Select an option to see the answer and solution.
A.N explosives detonated by
A. Primer
B. Detonator
C. Booster
D. All of these
Select an option to see the answer and solution.
During blasting operation in underground workings which have approached within 9m of each other the Shotfirer shall not fire in any of the faces unless some conditions are complied with. Which of the following is not to be observed as per CMR 2017?
A. all persons from both the faces are to be withdrawn
B. persons shall be withdrawn only from the face where blasting is going to be held
C. the place has to be fenced off to prevent inadvertent entering of persons
D. all persons shall take proper shelter as stated in the statutes
Select an option to see the answer and solution.
If the guide ropes are clammped in shaft to the girders in under ground decking level shaft may extend only . . . . . . . . m below the girder level.
Select an option to see the answer and solution.
If the black damp exceeds about . . . . . . . .% the atmosphere became non explosive irrespective of any percentage of firedamp.
Select an option to see the answer and solution.
The maximum number of detonators issued to have in the possession of Shot-firer during a shift shall never exceed the
A. need of shift targeted production
B. unit cost fixed for coal preparation
C. the number of shots fixed by CM
D. coal strength of the seam
Select an option to see the answer and solution.
The instrument used for counting and size of suspended cloud of aerosois.
A. Gravimetric dust sampler
B. Holographic counter
C. Tyndaloscope
D. Royco particle counter
Select an option to see the answer and solution.
There is no pressure drop between intake to return after installation of booster fan called . . . . . . . .
A. Neutral check
B. Natural line
C. Neutral line
D. All of these
Select an option to see the answer and solution.
Stone dust barrier may fail of located within . . . . . . . .m of face or other potential source of ignition.
A. 20 - 30
B. 0 - 20
C. 40 - 60
D. 60 - 80
Select an option to see the answer and solution.
Horizontal roadway parallel to strike of vein located either on footwall or hanging wall side.
A. Level
B. Drive
C. Cross cut
D. Rise drive
Select an option to see the answer and solution.
Person are not permitted to travel on.
A. Mine cars
B. Tubs
C. Conveyors
D. All of these
Select an option to see the answer and solution.
For measuring the area of roadway of irregular shape, a suitable device used called . . . . . . . .
A. Pentagraph
B. Planimeter
C. Profilo cheeter
D. Profilo meter
Select an option to see the answer and solution.
To prevent coal dust raising loading skips be arranged in the
A. DC shaft
B. UC shaft
C. Air shaft
D. All of these
Select an option to see the answer and solution.