When the occurrence of mineral (e.g. rare minerals) is randomly distributed in a rock then which of the distribution pattern is statistically followed?
Select an option to see the answer and solution.
Mining Engineering · all questionsIntroduction to Mining Engineering
Introduction to Mining Engineering
practice.
Practice every MCQ with options. Use Show answers when you want the correct option and solution.
403
Questions
1/21
Page
Pick an option on a question to see the right answer and solution.
Which of the following combination of SDL based mining is expected to give best production and productivity of SDL?
Select an option to see the answer and solution.
It is very difficult to control shaley roof if coal is not left with the shale why?
Select an option to see the answer and solution.
In connection with lowering or raising of persons by means of bucket etc. for a shaft exceeding "A" m in depth, there shall be significant cover overhead for protection from things falling down the shaft. A is given by
Select an option to see the answer and solution.
Match the following:
| Access | Haulage | Mineralisation |
| P Shaft | 1. Track | a. Moderate depth |
| Q Decline | 2. Trackless | b. Deep seated |
| R Adit | 3. Hoisting | c. Hillock |
Select an option to see the answer and solution.
In a mine deploying shovel and dumper, the distance from the crest of the bench to the centre of the dumper including safety berm and clearance is 7.5m, the dumping radius and the cutting radii of the shovel are 15m and 12m respectively. The width of the working bench of the mine in m is
Select an option to see the answer and solution.
In a room-and-pillar stope, bench blasting is conducted using ANFO having density of 800 kg/m3. The specific gravity of rock is 2.5, hole diameter is 100 mm and spacing to burden ratio is 1.3. The charge length of each blast hole is 80% of the hole length. For a desired powder factor of 0.48 kg/tonne, the spacing and burden of the blast pattern in m respectively are
Select an option to see the answer and solution.
A surface mine blast design has 9 holes in a row, each of 8m length and 200mm diameter. The spacing and burden are 6m and 5m respectively. The length of subgrade drilling is 1m and the density of in-situ rock is 2.43 t/m3. Considering an explosive density of 0.9 t/rn3 and stemming length of 2m, the powder factor from the blast in t/kg is
Select an option to see the answer and solution.
In a mine for one shovel six trucks are assigned. The shovel loading time per truck is 5 min, and truck cycle time 20 min. Calculate the match factor.
Select an option to see the answer and solution.
The following data are provided for a surface mine to be excavated by a shovel:
Production target: 10000 te/shift
Available hours per shift: 6 hrs
Shovel loading cycles per hour: 106
Bank density of the material mined: 2400 kg/m3
Swing factor at 120° swing: 0.91
Bucket fill factor : 0.64
Utilization of available time: 83%
No of working days in a year : 300
No of shifts per day : 3
The size of bucket of the shovel in m3 is
Production target: 10000 te/shift
Available hours per shift: 6 hrs
Shovel loading cycles per hour: 106
Bank density of the material mined: 2400 kg/m3
Swing factor at 120° swing: 0.91
Bucket fill factor : 0.64
Utilization of available time: 83%
No of working days in a year : 300
No of shifts per day : 3
The size of bucket of the shovel in m3 is
Select an option to see the answer and solution.
Which of the following support has maximum linear progress?
Select an option to see the answer and solution.
Every ladder way used in a mine shall project above the mouth of at least
Select an option to see the answer and solution.
Which of the following is most difficult in opening up an opencast mine?
Select an option to see the answer and solution.
In-situ ore of 1.5% Cu got diluted with waste rock of value 0.2% Cu. If the resultant extracted ore has 1.2% Cu. What is the percentage of dilution?
Select an option to see the answer and solution.
Top slicing is an underhand caving method which is a variation of
Select an option to see the answer and solution.
The diameter of holes in mm commonly used for ring drilling by drifters in sublevel stoping is between
Select an option to see the answer and solution.
Friction Clutch is used for
Select an option to see the answer and solution.
The process that sends sand water mixture in underground coal depillaring district is known as
Select an option to see the answer and solution.
Which of the following method of mining is only applicable to non-coal mines?
Select an option to see the answer and solution.
As per CEA 2010, the length of flexible cable used in portable and transportable apparatus shall not be more than
Select an option to see the answer and solution.