The transient current in an RLC circuit is oscillating when
Select an option to see the answer and solution.
A series RC circuit has R = 5 Ω and C = 10 µF. The current in the circuit is 5sin20000t. The applied voltage is
Select an option to see the answer and solution.
An RC circuit has an R of 10 kΩ and C = 0.05 µF. The applied voltage for charging is 36 V. How long will it take C to charge to 24 V?
A. 6.2 msec
B. 4.5 msec
C. 0.549 msec
D. 0.26 msec
Select an option to see the answer and solution.
Which one of the following statements is not a property of R-L driving point impedance?
A. The first critical frequency at the origin is a zero
B. The last critical frequency is a pole
C. The impedance at s = ∞ is always less than the impedance at s = zero
D. The slope of the impedance curve is positive at all points
Select an option to see the answer and solution.
In the circuit shown below, shown S is closed at t = 0. The time constant of the circuit and initial value of current i(t) are
A. 30 sec, 0.5 A
B. 60 sec, 1.0 A
C. 90 sec, 1.0 A
D. 20 sec, 0.5 A
Select an option to see the answer and solution.
A battery charger can drive a current of 5 A into a 1 ohm resistance connected at its output terminals. If it is able to charge an ideal 2 V battery at 7 A rate, then its Thevenin's equivalent will be
A. 7.5 V in series with 0.5 ohm
B. 12.5 V in series with 1.5 ohm
C. 7.5 V in parallel with 0.5 ohm
D. 1.25 V in parallel with 1.5 ohm
Select an option to see the answer and solution.
Energy needed to move 4 coulombs of charge is 4 joules. The potential difference is
A. 2 Volt
B. 1 Volt
C. 0.1 Volt
D. 0.2 Volt
Select an option to see the answer and solution.
The Z-parameter matrix
\left[ {\begin{array}{*{20}{c}}
{{{\text{Z}}_{11}}}&{{{\text{Z}}_{12}}} \\
{{{\text{Z}}_{21}}}&{{{\text{Z}}_{22}}}
\end{array}} \right] for the two-port network shown is
A. \left[ {\begin{array}{*{20}{c}}
2&{ - 2} \\
{ - 2}&2
\end{array}} \right]
B. \left[ {\begin{array}{*{20}{c}}
2&2 \\
2&2
\end{array}} \right]
C. \left[ {\begin{array}{*{20}{c}}
9&{ - 3} \\
6&9
\end{array}} \right]
D. \left[ {\begin{array}{*{20}{c}}
9&3 \\
6&9
\end{array}} \right]
Select an option to see the answer and solution.
Choose the incorrect answer related to mutual inductance
A. Mutual inductance is measured in Henry
B. Mutual inductance may appear either as positive or negative quantity
C. The current in a coil generates magnetic flux in the same coil and nearby coil, inducing a voltage in second coil
D. M12 = M21
Select an option to see the answer and solution.
Which statement is not correct? The given circuit is
A. Low pass filter
B. High pass filter
C. De-emphasis circuit
D. Integrator
Select an option to see the answer and solution.
You are given that L1 = 2 H and L2 = 8 H are perfectly lossless inductors which are magnetically coupled. The coupling inductance M in Henrys will be:
A. M = min(2, 8)
B. M < 2 2 + 8
C. D. Select an option to see the answer and solution.
A network in which all the elements are physically separable is called a
A. distributed network
B. lumped network
C. passive network
D. reactive network
Select an option to see the answer and solution.
Consider the circuit shown below
The power factor of the above circuit as seen by the source is
A. 0.988 lag
B. 0.988 lead
C. 0.235 lag
D. 0.235 lead
Select an option to see the answer and solution.
What is the minimum number of elements required to realize a given driving point susceptance function?
A. One greater than the total number of internal poles and zeros
B. Equal to the total number of internal poles and zeros
C. One less than the total number of internal poles and zeros
D. None of the above
Select an option to see the answer and solution.
In a circuit in which resistance, capacitance and inductance are in series, the impedance would be-
Select an option to see the answer and solution.
For maximum power transfer to load, find the value of 'Z
L '
Select an option to see the answer and solution.
The value of resistance R shown in the given figure is
A. 3.5 Ω
B. 2.5 Ω
C. 1 Ω
D. 4.5 Ω
Select an option to see the answer and solution.
For a network shown in figure, which of the following statement is true.
A. Reciprocal and symmetric
B. Reciprocal but not-symmetric
C. Symmetric but non-reciprocal
D. Neither symmetric nor reciprocal
Select an option to see the answer and solution.
The effective inductance across 'AB' of the infinite ladder shown in the figure below is-
Select an option to see the answer and solution.
What will be the power consumed by the voltage source, current source and resistance respectively?
A. 1W, 1W, 2W
B. 0W, 1W, 1W
C. 1W, 0W, 1W
D. 0W, 0W, 0W
Select an option to see the answer and solution.